Intake Manifold Replacing on Acura?

Intake Manifold
REMOVAL & INSTALLATION: ---

The details are provided below :---

2001-02 Models

1. Before servicing the vehicle, refer to the precautions section.
2. Remove or disconnect the following: 
   
   
   Negative battery cable

   Evaporative Emissions (EVAP) control canister hose and vacuum hose

   Air intake tube

   Intake manifold cover

   Accelerator cable

   Cruise control cable

   Brake booster vacuum line

   Intake manifold vacuum line

   Positive Crankcase Ventilation (PCV) valve and hose

   Intake Air Temperature (IAT) sensor connector

   Idle Air Control (IAC) valve connector

   Throttle Position (TP) sensor connector

   Manifold Absolute Pressure (MAP) sensor connector

   Intake manifold 
   
   
   

   Fig. Exploded view of the intake manifold-2001-02 models

To install:

Fig. Intake manifold torque sequence-2001-02 models

1. Install or connect the following:
   
   
   New intake manifold gasket

   Intake manifold. Tighten the fasteners in sequence and in several passes to 16 ft. lbs. (22 Nm).

   MAP sensor connector

   TP sensor connector

   IAC valve connector

   IAT sensor connector

   PCV valve and hose

   Intake manifold vacuum line

   Brake booster vacuum line

   Cruise control cable

   Accelerator cable

   Intake manifold cover

   Air intake tube

   EVAP control canister hose and vacuum hose

   Negative battery cable
2. Start the engine and check for proper operation.

2003-06 Models

1. Before servicing the vehicle, refer to the precautions section.
2. Remove or disconnect the following:
   
   
   Negative battery cable

   Intake manifold cover

   Intake Air Temperature (IAT) sensor 2 connector

   Air intake tube

   Positive Crankcase Ventilation (PCV) hose

   Brake booster vacuum line

   Intake manifold vacuum line

   Evaporative Emissions (EVAP) control canister hose and clamp bracket

   Water bypass hoses from the throttle body and plug the hoses
3. Remove the following electrical connections and clamps from the manifold:
   
   
   Intake Air Temperature (IAT) sensor 1 connector

   Throttle Position (TP) sensor connector

   Manifold Absolute Pressure (MAP) sensor connector

   EVAP canister purge valve connector

   Intake Manifold Runner Control (IMRC) actuator connector
4. Remove or disconnect the following:
   
   
   Upper cover bolts and nuts in the sequence illustrated using two or three passes

   Intake manifold bolts in the sequence illustrated

   Intake manifold and spacer
   
   

   

   

   Fig. Exploded view of the intake manifold-2003-06 models

   
   
   

   

   

   Fig. Upper cover loosening sequence-2003-05 models

   
   
   

   

   

   Fig. Intake manifold loosening sequence-2003-06 models

To install:

1. Install or connect the following:
   
   
   New intake manifold gasket and spacer

   Intake manifold. Tighten the fasteners in sequence and in several passes to 16 ft. lbs. (22 Nm).

   Upper cover bolts and nuts in the sequence illustrated using two or three passes to 9 ft. lbs. (12 Nm)
   
   

   

   

   Fig. Intake manifold torque sequence-2003-05 models

   
   
   

   

   

   Fig. Upper cover torque sequence-2003-06 models
2. Connect the following electrical connections and clamps to the manifold:
   
   
   Intake Manifold Runner Control (IMRC) actuator connector

   EVAP canister purge valve connector

   MAP sensor connector

   TP sensor connector

   IAT sensor 1 connector

   Water bypass hoses to the throttle body

   EVAP control canister hose and clamp bracket

   Intake manifold vacuum line

   Brake booster vacuum line

   PCV hose

   Air intake tube

   IAT sensor 2 connector

   Intake manifold cover

   Negative battery cable
3. Start the engine and check for proper operation.

This details will help.

Thanks.

FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html