@

Friday, March 9, 2012

How to replace Valve Covers on Ford And Mercury?

The details are for 2008 and 2008 ford Taurus and Mercury Sable car models.


Valve Covers
REMOVAL & INSTALLATION
SEAL REPLACEMENT

Instructions are as follows :----


Removal & Installation



Left Side
Specific to:
Ford Taurus 2008-2009
Mercury Sable 2008-2009
  1. Remove the LH ignition coils.
  2. Remove the oil level indicator.
  3. Disconnect the LH variable camshaft timing (VCT) solenoid electrical connector.
  4. Detach and disconnect the 2 engine control wiring harness electrical connectors.
  5. Detach all of the wiring harness retainers from the LH valve cover stud bolts.
  6. Disconnect the 3 LH fuel injector electrical connectors.
  7. Loosen the 11 stud bolts and remove the LH valve cover. Discard the gasket.
  8. Inspect the VCT solenoid seals and the spark plug tube seals. Replace as necessary. Refer to SEALS.
  9. Clean the valve cover, cylinder head and engine front cover sealing surfaces with metal surface cleaner.
To install:

NOTE
Installation of new seals is only required if damaged seals were removed during disassembly of the engine. Refer to SEALS.


NOTE
Failure to use the correct Motorcraft High Performance Engine RTV Silicone may cause the engine oil to foam excessively and result in serious engine damage.


NOTE
If the valve cover is not installed and the fasteners tightened within 4 minutes, the sealant must be removed and the sealing area cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Failure to follow this procedure can cause future oil leakage.

  1. Apply an 8 mm (0.31 in) bead of Motorcraft High Performance Engine RTV Silicone to the engine front cover-to-LH cylinder head joints.
  2. Using a new gasket, install the LH valve cover and 11 stud bolts. Tighten in the sequence shown to 89 inch lbs. (10 Nm). 

    image
    Fig. LH valve cover tightening sequence
  3. Connect the 3 LH fuel injector electrical connectors.
  4. Attach all of the wiring harness retainers to the LH valve cover stud bolts.
  5. Connect and attach the 2 engine control wiring harness electrical connectors.
  6. Connect the LH VCT solenoid electrical connector.
  7. Install the oil level indicator.
  8. Install the LH ignition coils.
Right Side
Specific to:
Ford Taurus 2008-2009
Mercury Sable 2008-2009
  1. Remove the RH ignition coils. Refer to Section 303-07 .
  2. Detach and disconnect the RH catalyst monitor sensor electrical connector.
  3. Detach and disconnect the RH heated oxygen sensor (HO2S) electrical connector.
  4. Disconnect the RH variable camshaft timing (VCT) solenoid electrical connector.
  5. Disconnect the 3 RH fuel injector electrical connectors.
  6. On early build engines, disconnect the heated PCV valve electrical connector.
  7. On all engines, detach all of the wiring harness retainers from the RH valve cover stud bolts.
  8. Remove the nut and the power steering pressure (PSP) tube bracket from the valve cover stud bolt.
    NOTE
    It is necessary to reposition the A/C tubes to remove the valve cover.
  9. Loosen the bolt, the 10 stud bolts and remove the RH valve cover. Discard the gasket.
  10. Inspect the VCT solenoid seals and the spark plug tube seals. Replace as necessary. Refer to SEALS.
  11. Clean the valve cover, cylinder head and engine front cover sealing surfaces with metal surface cleaner.
To install:

NOTE
Installation of new seals is only required if damaged seals were removed during disassembly of the engine. Refer to SEALS.


NOTE
Failure to use Motorcraft High Performance Engine RTV Silicone may cause the engine oil to foam excessively and result in serious engine damage.


NOTE
If the valve cover is not installed and the fasteners tightened within 4 minutes, the sealant must be removed and the sealing area cleaned. To clean the sealing area, use silicone gasket remover and metal surface prep. Failure to follow this procedure can cause future oil leakage.

  1. Apply an 8 mm (0.31 in) bead of Motorcraft High Performance Engine RTV Silicone to the engine front cover-to-RH cylinder head joints.
  2. Using a new gasket, install the RH valve cover, bolt and the 10 stud bolts. Tighten in the sequence shown to 89 inch lbs. (10 Nm).

    Click image to see an enlarged view
    Fig. RH valve cover tightening sequence
  3. Install the PSP tube bracket on the valve cover stud bolt and install the nut. Tighten to 62 inch lbs. (7 Nm).
  4. Attach all of the wiring harness retainers to the RH valve cover stud bolts.
  5. On early build engines, connect the heated PCV valve electrical connector.
  6. On all engines, connect the 3 RH fuel injector electrical connectors.
  7. Connect the RH VCT electrical connector.
  8. Connect the RH HO2S sensor electrical connector.
  9. Connect the RH catalyst monitor sensor electrical connector.
  10. Install the RH ignition coils.

Seal Replacement



  1. Inspect the VCT solenoid seals and the spark plug tube seals. Remove any damaged seals.
  2. Using the special tools, remove the seal(s).

    Click image to see an enlarged view
    Fig. Removing valve cover seals
To install:

NOTE
Installation of new seals is only required if damaged seals were removed during disassembly of the engine.


NOTE
Spark plug tube seal installation shown, VCT seal installation similar.

  1. Using the special tools, install new VCT solenoid and/or spark plug tube seals.

    Click image to see an enlarged view
    Fig. Installing valve cover seals



This details will help.
Thanks.


FOR MORE HELP GO TO: ---

Car repair guide?

http://technoanswers.blogspot.in/2012/03/car-repair-guide.html


No comments:

Post a Comment

@